Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am trying to run the SDK15.3.0 gfx example code - only changing line 82 to:
And also I have changed the sdk_config to the display's width and height. I have wired it...
hi
I want to update RTC time in my device nrf52840 through nrf connect app. How can i do this? Is there any related example which may help me in doing this?
Hi,
I'm attempting to use OpenOCD to perform the equivalent to "nrfjprog --recover", since we've recently started using that feature.
I read through this case, but it...
Version 4.20a (Win x64) of Segger's Embedded Studio has problems with it's C syntax highlighting -- specifically conditional compiled sections of code. Code that is not being...
Hi,
We are using nrf52840 to develop a cryptocurrency hardware wallet. We want that user can verify that the device is authenticate. In order to authenticate, the desktop...
Hi,
I'm using Kail and I have a project with original target device nrf52832xxAA, I need to change it to nrf52832xxAB (the device onboard is nRf52832QFAB).
When I...
Hello,
I have to send SMS from NORDIC nrf9160dk which is using iBASIS sim card to my mobile phone. For this I tried two programs (at_client and simple_at). But nothing works...
Hello,
I am trying to run https://github.com/sigurdnev/fw-nrfconnect-nrf/tree/master/samples/nrf9160/i2c_scanner exampl. It is not compiling with the zephyr right now...
Hi,
for a new project we use the NRF52480, I can get it into low power mode with a total use of 20µA ( with all the other hardware on the board ). But when I initialize...
As far as I can tell, the packet sent by nRF24L01+ PTX only contains a destination address. There if no information that identifies the transmitter (i.e. PTX).
So, when...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
