I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
hello, i have a question, i use sdk15.3 for nRF52832, i run for example flash_fds, sometimes it will not be able to erase or write to memory, after restarting the device,...
I'm having a problem that I get some presumable interference between a high flash memory activity and UART communication. I'm writing single words into flash quite often,...
I am working on a mesh network and i want to add a nordic thingy 52 to read temperature & humidity data over the mesh, let say to an nrf52 DK connected to a Raspberry Pi,...
I'm developing a Zigbee coordinator that works as an On-Off Switch for the Zigbee Profile HA: this connects to the Device Mains Power Outlet, again with the HA profile.
...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
I have a Coordinator that implements the Window Controller Device of the HA profile...
Hi folks,
Im trying to run the heart rate collector from a Visual Studio application and I have some communication issues with the connectivity device. I use a nRF52 Dongle...
I'm currently looking a bit into the bearer-layer internals of the nRF SDK for Mesh and noticed that there is a heap of instances where data needs to be transferred between...
Hi,
I am using nRF52840 and BLE coexistence (mesh and ble). I am able to connect to my board via BLE using nRFConnect for PC and a nRF52840-DK and change characteristics...
I'm trying to use DFU for the first time
I'm working my way through these instructions:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
The SDK v16 package has a board file for the nRF52833 board, PCA10100, however this seems to reference GPIO pins which are not present on the device:
What should these values...
We use the nrf52832 in twi-master mode. The connected slave sometimes needs longer to respond than the default configured TWI timeout.
The timeout is defined inside the...
Is it possible to generate a zip package containing both firmware and softdevice in such way that the soft device will be updated only if the current device softdevice version...
I have some module chip connected to the nRF9160 DK providing the sensor data over I2C line. In some state transition of the module the short reset pulse needs to be generated...
Hello, I am using BLE secure bootloader example on nRF52840 with SDK 15.3 and softdevice 61.1. I can see the bootloader protects the MBR page and Bootloader space using ACL...
When I run "AT+COPS=?" WITHOUT a SIM the modem always responds properly.
When I run "AT+COPS=?" WITH a SIM the modem does not respond as expected. I get error after approx...
