hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
We have an application for using the 802.15.4 protocol with a nRf52840 and a Front End Module. We are looking for an approach to take for integrating the FEM control into...
Hi,
I'm trying to figure out if my device is suffering from errata 172.
* How can I know if I'm using Ble_LR125Kbit or Ble_LR500Kbit? * I'm trying to use the function...
To the kind attention of Nordic support team,
I would like to do a question that is not strictly related to Nordic, but I hope your expert can kindly give me an answer,...
Hello,
I am a student who tries to make a smart IoT project using nRF9160 DK and Arducam OV5642. I am searching on the internet to where to start, but I cannot find any...
If all you need is changing PHY, Tx power and Device Name in a standard nRF52840, do you need building a new bootloader from the scratch or the is a way to edit the standard...
Hello,
I'm experimenting with the nRF SDK for Mesh v3.2.0 and a nRF52832 DK, specific with the LPN example.
I want to enable BLE DFU support so I followed the instructions...
I am programming with SDK15.0. Then I use nRFgo studio to download the merged program to the DK board. But it reported a validation failure. So I tried to download softdevice...
I am building a project that is based on the custom service example https://github.com/bjornspockeli/custom_ble_service_example but I don't like how it advertises in a way...
Hi!
I am trying to test the Immediate Alert Client application example (ble_app_ias_c) from nRF5_SDK_15.0.0 on my nRF52832 based module. I want to understand how to test...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
