Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everyone. Now am trying to reset all register values of the NRF24 to their default values according to the datasheet. When i probe the process on a saleae analyzer, i see...
Hi all,
Our company needs a BLE Sniffer and I've stopped my attention on nRF52 DK board. As stated in its documentation a SEGGER J-Link is necessary to upload the nrf sniffer...
I wrote my program on PCA10056, N52840, with fds_init() it everything was working fine. Now using the same main.c file I wanted to program a N52832 which comes to PCA10040...
I am very new to Nordic products so please excuse my ignorance.I have been trying to put my nrf52840 board to deep sleep. It seems to go to sleep but when I try to wake it...
Hi,
I'm porting code from Simblee/Arduino to Laird's BL651/Nordic SDK (nRF52810, SDK 15.3, S112). (Simblee discontinued.) For accurate timing of a GPIO pin, I use TIMER1...
Is anyone else having issues with the Zephyr shell on the NRF9160 DK? We weren't able to get it working on our code, so we went back to the coap_client applications in the...
Hello,
I was working with Asset Tracker sample and tried to add LTE device in Cambridge, UK. It worked, both LED 3 and 4 were blinking and added device to the nRF Cloud...
In advance I would like to say I’m sorry for the frustration that this message reflects…Event though I have been using the UART for some time, adding more functionality makes...
On nRF52832,
A1> Out of the Softdevice scope: if we are using RTC and have LFCLKSRC configured to XTAL source and if XTAL source gets turned off for some reason what happens...
Hi,
I am struggling with a low power consumption solution for waking the NRF52832 with our product which is using a third part module.
Currently our product total power...
Hi, I have Lenovo tab E8 tablet with Android 7.0 and I connect to a BLE device (nrf52832 SDK 15.2.0 S132) from my Qt 5.11.2 app. After succesfull connection I discover services...
The toolchain setup of the NRF91 is extremely complicated. Is the a VM Image or Docker container that has everything pre-configured? I am trying to setup up a linux VM now...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
