Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
With mesh dfu, whether to upgrade the firmware of many different devices at the same time is supported. Multiple device deployment spaces are adjacent, and simultaneous transmission...
How to fix this error: Installnnnnfgo Studio tips can't find nrfjprog.dll The development environment is: windows 10 Pro 64-bit operating system MDK-ARM Plus Version5.20 nRF...
Hi,
I am in the process of converting a large freertos project from nRF52832/SDK14.2 to nRF52840/SDK16.0
I've managed to convert everything but the buttonless DFU...
I seem to be getting odd behavior of the UARTE0. Actually, this same behavior happens with the standard UART0.
I have a loop that sends a two byte message every 1 second...
Dear Nordic Support,
I just got my Thingy:91 and I followed your Getting started guide. I registered the SIM card successfully but whenever I reached this step, it always...
According to the nrf52810 v2.1 data sheet, the radio draws 7.0 mA at +4 dBm TX power and 4.6 mA at 0 dBm TX power.
How much power is consumed at transmit levels from -4...
I live in Vietnam, I try to use NRF9160 dev board to connect LTE and NB-IOT but device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect...
Hi
I am using fafs example from SDK 15.0.0
It was possible to write to the SD card by SPI communication. However, using SanDisk's 32GBSDHC, it became impossible to write...
Hello
I have both mai.c and app_sdcard.c "static const nrf_drv_spi_t spi = SPI_INSTANCE (spi_instance);" Want to use .
So using "extern"
main.c
app_sdcard...
I have already developed a beacon with nrf52840, but now I need to detect it with another nrf52840, but my problem is taht I need to use less power as possible, so I need...
Hi guys, after building and running a mesh network i've been wokring on, i ended up with an error
im wondering where i'd be able to find the mesh error table.. i can't...
I have custom board with BMP280 sensor & nrf 52832.I have interfaced BMP280 using twi interface. I am using SDK 15.2.0. and soft devices s132 V6.1.0 to transmit advertising...
We would like to achieve following:
Only peripheral devices should advertise data toward only central devices in the same application.
advertising data by peripheral...
Greetings! I'm trying to set up an nRF52 board as an SPI slave so that it would receive chunks of data irregularly from the master device (a Raspberry Pi in this case, if...
