Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
I'm currently designing a system that requires Nonvolatile memory. Whilst I can accept the 43uS delay to write a word to flash memory. My concern is that it is entirely possible...
Hello,
i plan implementing an block storage for nRF51. I want to integrate an checksum or error correction mechanism.
I have understood i can write an bit 20000 times...
i meet very strange problem! i using nRF51822 QFAC. it has 32K RAM. but when we using 32K RAM Linkscript file. the firmware did not run up. it seem dead in sd_ble_enable(...
Greetings,
S110 with SDK6.0 I try to build the executable for Nordic GitHub project Timeslot Oberver example. I get an error that the handler SD_EVT_IRQHandler is multiple...
Hi,
There is a following initialization in 51822:
static void controls_init(void){
uint32_t err_code;
// Configure pins.
uint32_t pins_transition_mask = (1 << SCKIN_PIN...
I'm working on a project using the nRF51822 beacon kit (PCA20006), and I've downloaded the firmware files installer from the website. After running the installer, I can see...
Hello,
I have a ptr5518 module which has nRF51822 in it. I need help programming the device. I am new here so a detailed help will be very useful.
I want to use the built...
Hi,
I'm workin with nRF51822 as peripheral device. is it possible to retrieve the device name of the central at the moment of the conection i mean when is generated the BLE_GAP_EVT_CONNECTED...
