I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Just two questions regarding the new nRF52840 to make sure I've understand it correctly;
For the NFC, this is passive only? So it acts like a tag and is not able...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...
Hello!
I'm trying to use the ram_retention in sdk 15 alpha to retain RAM in system off mode and do some power profiling.
The default code seems to retain 8 kB of RAM...
My project needs to use 2 different TWI instances and 1 SPI instance. I knew that it is not possible to use three instances at the same time in nRF52.
To implement 2 TWI...
Hi Nordic,
I am trying to enable the DC/DC converter on a PCA20006 rev 1.3.0.
I am using the softDevice S130.
1. Using the sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi.
I am using saadc example code or SDK V13 with the following requirements:
Voltage input up to 70mV,
Resolution: 50uV
So I did some modification to support...
Hello,
yesterday I got a Thingy:52 device at an event held in Frankfurt/Germany. At home I've tested the DFU for the latest firmware and observed that the image was transfered...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...