Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I want to use AES ECB block present on nrf51 and nrf52 boards for resolvable private address (RPA) generation.
Are there any measurements about how much battery the...
I have an iot/coap environment setup and i want to read input voltage connected to p0.01.I can read the input in terms of resolution(0-1023).I can convert this values to voltage...
I have a project where I need both TWI instances as well as an SPI instance to be used with sdcard and fatfs libraries. When I try to compile I get the error: SPI1_TWI1_IRQHandler...
hi,everyone,I want to ask who know why sdk11.0 ble_ancs push message without push App Identifier?I look at the print, push the news started with tittle ,and the "p_attr -...
Hi!
I'm trying to use a custom made whitelist with my scanning device, but no data is arriving.
Is there something I need to do at the advertising devices? Here is the...
Hi, I have a custom board based around the nRF51822 which I programmed via SWD with the ble_app_hrs_pca10028_s130.hex image provided in the SDK, however when checking with...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
Hello everbody,
I made some current measurements with mit DK nRF52 and the nRF52832 Chip.
Everythings works fine, but I always get "peaks", as you can see on the Picture...
I am using nRF52 pca10400 and I would sample some audio signal for short periods of time, but I found a lot of difficulties with the SAADC example from sdk 13, since if I...
Hi,
I want to collect sensor-data, save it to flash and access it later.
I´m not quite familiar with ways to save data and get a little bit confused by the fds library...
Hi,
We are currently facing this issue, where after a DFU application firmware update (or bootloader update) the bonding information gets wiped out.
We are using a custom...
Hi,
I'm trying to control LSM6DS3 by TWI communication.
Slave address of the chip is 0xD4 when SDO/SA0 pin is low.
I'm using SDK13.0.0.
My code is like below.
...
I will test the receiver blocking of ETSI with the nRF51822 module
(EN300328 V2.1.1 2016-11 5.4.11 Receiver Blocking).
However, please tell me the next items because I do...
I'm testing the setup for the Receiver Blocking test ask part of EN 300 328 V2.1.1 and I have a question after reading these posts devzone.nordicsemi.com/.../ , devzone.nordicsemi...
Hi,
We have some custom boards with NRF51822 and the S110 (v8.0.0) softdevice, on which we have programmed the dfu dual bank bootloader, based on the example one from the...
