Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hi,
I use nRF52832 with sdk 12.2.
and I running the ble_app_hrs_c example code on pca10040 evb.
I can scan many hr devices but polar h7 heart rate not.
I check Iphone...
Hi I use nRF52832 and move my project to SDK13.
I want to use debug mode in keil-c and try to find after ble_db_discovery_start function call why no csc_c_evt_handler_t call...
I'm working on an OTA firmware update process, using my own bootloader and application. To understand the process' limitations, I need to know to what extent one can update...
hello everyone：
how many timers can i open in nrf51822(QFAA) with SDK9.0? the APP_TIMER_MAX_TIMERS's max value
#define APP_TIMER_MAX_TIMERS 13 /**< Maximum number of...
Hello,
I am referring to this link
www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules
and I am referring to Xuntong PTR5518 11 15x15x2mm PCB China product...
I see BLE_GAP_EVT_SEC_PARAMS_REQUEST generated from SD. How to call this request for pairing state?
I can't find any peer manager in the project.
Explane, pls.
Following is a simple application that I have created. It has no softdevice and the configuration is very similar to blinky freeRTOS example.
Source code:
main.c
...
Hello ,
I'm working on custom board, I'm trying to disconnect from the Central (Andriod app) when the battery is below certain level and stop re-advertising.
Below is...
In s130 Soft device v2.0 document, it says it can have role with up to 8 Role concurrent with Central, Pheripheral, Advertiser, Observer.
I'm not sure i've understand all...
Hello. I'm using nRF52832, PCA10040, SDK13, S132 and "ble_app_uart" as reference.
When I connected board through by bluetooth, I couldn't see notification message which...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
Hi Nordic team,
I print logs at each function in ble_bas.c. I used the App of nRF connect to test BAS. I can see on_connect, on_disconnect and on_write at enabling/disabling...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
