Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I just went through the release-notes of the S132 and found a passage that the s132_nrf52_4.0.0-1.alpha introduced some new ble-features like f.ex. the role-configuration...
Hi!
I'd like to collect statistics from BLE physical layer, namely about errors that have occurred in receiving packets on a BLE advertisement channel. I see from custom...
Hello, I working on nRF52DK, for programming am using Eclipse IDE. For that I am following nordic tutorials here
I need to add a new project it does't have any makefile...
Hello dear Engineers!
the questions are should I connect pins DEC2:A18 and DEC2:E24 externally ?
shuold I use Capacitors to decouple both these pins (in Reference no...
Dear developers,
we are considering purchase of a reliable programmer capable to flash the nRF51822 in production, one possible option is the SEGEGR FLASHER PORTABLE or...
Hi!
I have noticed strange problem with one of GPIOs - P0.15. We have tested 50 devices based on nRF52832 and 3 of them have problem with P0.15 after few days.
P0.15...
The default I2C address of my sensor is 0x29 (7-bit).
If the least significant bit is low (0x52) the message is a master write to the slave. If the lsb is set (0x53) then...
I'm using SDK 12.2.0 with softdevice S130 V2.0.1 and want to use TWI.
Using the ble_beacon example I added the twi code from twi_sensor.
Shortly after calling TWI_Init(...
Hi,
during normal operation, my device shows a power consumption of 4.7mA.
Normal operation is:
accelerometer (lis2dh) detects a shake and wakes up the nrf51 via...
Hii ,
i am using customized board (chip : BT832).
err_code = sd_softdevice_enable(clock_source, softdevice_assertion_handler); hangs. it took some delay and after that...
Hi all,
I have seen a pair of questions ( this and this ) that I think have something to do with this, but didn't find a solution.
I have a custom board with a button...
I want to have an application similar to UART in the SDK example, with multiple peripherals.
I tried to modified existing UART example, but cannot make the central node...
I want to add the nrf52832 to my customized board and I am studing the possibilities for flashing it once that is located on the board. Is it possible to flash trhough the...
I have a board with some LEDs that are driven in the same way as with the nRF51 DK board (i.e. there is a resistor in series with the LED and you drive the pin low to turn...
In our testing we encounter some devices (Centrals with nrf52832), where the peer manager event PM_EVT_BONDED_PEER_CONNECTED contains a invalid peer id 0x4000 (allowed values...
