Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'll try to simplify my project as much as possible to make this understandable.
I'm wiring an nRF52 PCA10040 board to an iCE5LP (Lattice) FPGA.
I'm having an issue with...
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon . It should act as an NRF51 USB dongle (pca10031-like) but...
My pc server should send information to nrf52832 by ECDH, then I create a dll file from micro-ecc. However,the result in windows is not the same as the result in nrf52832...
dear friends ,
within a peripheral connection event, 9 states is identified, as it is shown in the pic above(from s132 document). Can i get a detailed description about what...
Hi @ all,
I am working with IoT SDK 0.9 and nRF52DK.
I have trouble with the lwIP CoAP client example.
Everything works so far, the board is connected and I'm able...
Hello! I am using a custom board that contains a nRF52832 device. The board has the SWDIO and SWDCK lines connected, which I have successfully been using to flash and debug...
I'm migrating to the new 13.0.0 SDK and I'm wondering what are the benefits of using nrf_serial over app_uart (if any) and what steps I would need to take to switch over if...
I have successfully manged to achieve serial communication between my PC (Windows) and nRF52 board by using the pc-ble-library and the pc-ble-library-js .
I can run without...
Hi, I updated nrfutil to use in new sdk 13, but when I type "nrfutil pkg generate --help" I can't see the code for Softdevice S132 v4.0.2 (0x98) as indicated in this guide...
I have done erase all thing.
But in the second step, I am getting following error.
nrfjprog --program s132_nrf52_3.0.0_softdevice.hex
ERROR: The --family option given...
Hello,
I'm following the steps listed in the nRF5_IoT_SDK documentation and would like to connect the nRF52 to my Raspberry Pi 3 router. I have the RPi3 enabled for 6LowPan...
Hi,
I have exactly the same problem as in question devzone.nordicsemi.com/.../
but I can't find the solution.
When I erase all from memory, debugging works. If I flash...
Hi
We have been able to set LE authenticated payload timeout via the following functions:-
ble_opt_t opt = {0};
opt.gap_opt.auth_payload_timeout.conn_handle = ValidHandle;...
Hi there,
I am currently using nRF52832 to communicate with a digital sensor ship. The sensor chip generates an interrupt every time when data is ready to read via SPI...
