after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
Whenever our battery runs to zero, or if we have a reset due to voltage droop, the unit will not auto-connect and the user is forced to "forget" the device in iOS bluetooth...
Hello,
i'm trying to use nRF UART driver (nrf_drv_uart) to implement a high level UART manager.
I followed indications on SDK documentation but it doesn't work and i think...
Working on a project to set up a bidirectional UART to SPI link over ESB with nRF52832 (PCA10040), using SDK 13.0.
Working from provided examples for PTX and PRX, I manage...
Hello,
I've implemented one custom service very similar with NUS. I have two peripherical devices that are running in two PCA10040 with S132 12.1, and one central device...
I have set up some code using the ESB example in SDK v12.2.0 I and am able to transmit and receive packets between two nrf51 dongles, with no issues. However, when I program...
Hi,
I did time measurements for packet transmission (notification) and saw only ~ 30 microseconds (about 1000 ticks with 0 prescale) difference between sending one or up...
Hi,
I am using nrf51822 chip. I am using RTC to generate irq with CC. Everything works fine for IOS and old Android version. New android version makes 2 things when I disconnect...
I own a Surface Pro 3 which has only one USB-Port. Can I set up nRF-Connect with the internal Bluetooth instead of using an USB Hub to connect two development kits?
To whom it may concern.
Ended up on the Nordic Semiconductor website, since I was trying to find a good manufacturer for a Health Smartband and software.
I represent...
Hello, I want to use multiceiver mode nRF24l01. For 4 transmitters.
When setting up the receiver, I can only receive data from the tube 0.
I can not understand how to tell...
Hi all, I'm working on SDK13.0.0 secure bootloader and I'm curious to know about
Why nordic defined, dfu service uuid(0xFE59) is 16-bit uuid and characteristics in...
Hello,
I am attempting to use GCC with Eclipse. I have installed all the tools, sdk, etc. and have also installed Mentor Sourcery CodeBench to get the Make and rm tools...
Hello,
I'd like to know if it's possible to use this chip to analyze the spectrum in the range of 800MHz 1GHz, and if it's possible to capture raw data. With the information...
