I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
Hello,
We are migrating from IAR 760 to IAR 8.10 compiler does not produce the same assembly for the SDK12 inline function nrf_delay_us.
The original C Function is :
...
Hi, i am working on RTLS project. In beacons i want to enable DFU service using SDK 13.0. But I could'nt find a gothrough process to do the same. Please give me some link...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
Hallo Community,
I am doing the example ble_app_uart using Eclipse, a SDK 13.00 and a board 10040, When i compile the main file I´ve problems with scan params:
#if ...
#define UART_TX_BUF_SIZE 1024
#define UART_RX_BUF_SIZE 1024
Why to send and receive buffer length of the definition of 1024 bytes, increase the value, again if serial port...
Hi, I just bought the PCA10031 nRF51422 based USB dongle and PCA10028 nRF51422 based development board.
The difference between nRF51822 and nRF51422 was the ANT protocol...
Can I use below code to send data packets continuously over nus (>20 packets)
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{
if(i>20)
{
while((err_code = ble_nus_string_send...
Hi,
I am using nRF52 chip with SDK13.0. MTU size 155.
I am connect with device using android phone. After sending 1 byte command device starting to send continuous notification...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
