Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi,I have tried to write some characters like device name for BLE device. When I called
Code:
grantPermissionCharacter?.service.peripheral.writeValue(data1, for: grantPermissionCharacter...
The bluetooth icon in the status bar is gray, not white although I connected ble_app_hts(PCA10028) with nRF Toolbox(android app).
Doesn't android recognize connection state...
Hello,
using buttonless_dfu app, the app switch to bootloader as the upload is started with nrf toolbox on android,
but with iOS, the upload never starts the LOG error is...
The Bluetooth Mesh SDK is currently tagged as alpha software. Is there a timetable for its progression into beta and to a stable release?
I'm evaluating the nRF52832 for...
Hi, currently I'm working on ultra low power device. This device need to be wake up in 333 ms interval. I use RTC for this. My question is about strange current spikes with...
Hi,
I am using the nrf52 DK (PCA10040) and have a problem with the USB-UART. For some reason I do not see any log messages in the terminal.
I started with the "coap server...
I used SEGGER Embedded Studio to make ble_mesh_v0.9.1-Alpha project, there was an error while executing the flash_area_is_valid function, this problem occurs in the NRF51822...
I'm using the PCA10028, ble_app_hrs_dfu(sdk11).
Only the three screens below were repeated infinitely when I started to upgrade the softdevice through DFU.
And the...
My android version is the Kitkat.
The nRF Toolbox cannot find services when I changed the application of PCA10028 for example from ble_app_hts to ble_app_hrs.
The message...
Hi I am developing an application for sending data over BLE which I have received over SPI from a non - Nordic chip. I am using the ble_app_uart template for this. But data...
My call to sd_ble_gap_ppcp_set is returning NRF_ERROR_INVALID_PARAMETER.
I have the following connection interval settings:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500...
I am running SDK12.3 on an nRF52 and the bootloader on my boards has no problem replacing the application through the DFU process. Now I found a mistake in the bootloader...
I am not sure whether there is a small error in a Gazell packet transaction diagram, or if I have an incorrect understanding. From Gazell user guide :
If only the ACK...
Hi,
I am trying to achieve the maximum throughput when using the nRF51822.As far as I know, the minimum connection interval is 7.5ms and the maximum packets per interval...
