I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
I would like to use twenty concurrent connections. As I understand I should set ble_cfg.gap_cfg.role_count_cfg.periph_role_count = 20 and ble_cfg.conn_cfg.params.gap_conn_cfg...
Hello,
I have read with a lot of interest the documentation associated to the "multiprotocol support" associated to the nRF5 SDK for Thread v0.10.0.
As far as I understood...
This is a more specific counterpart to a question I posted on StackExchange . If you want to know more about the attack itself, check that out, but here, I'm asking for a...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
In order to prevent communication from middle-man attack, I append the signature after ECDH publickey. However, though I get the correct share secret by ECDH, I fail in verifying...
Hi,
I'm using the bluetooth 5.0 and base on the mutilink_center example to add a peripheral and a center. Because I want the center to connect two type device. It could...
Hello,
I have two identical devices with Laird's BL600 chip (that uses NRF51822). They are initialized as NRF_GZLL_MODE_DEVICE and use GZP library (without encryption ...
Hi,
I am trying to write my own bootloader. I gather new image via serial and store it in flash in my application at 0x30000 then invoke reset and in bootloader I want...
Hi,
I was testing the pwr_mgmt project in the nRF5_SDK_13.0.0 with my 52DK, the system off mode seems work fine ,cause the log information is right,but the question is...
Hi,
We are working with NRF 51822 in a multi-role arrangement (SDK 12.3.0, s130_nrf51_2.0.1_softdevice) where one NRF51 will be connected to a phone in peripheral mode and...
when i use pc tools or APP except "nRF Connect" to connect my 51822,i can not find some parameter,so i want to know in example "ble_app_uart",how to set up connect parameter...
So apparently, for ble, all CCCDs, regardless of what the UUID of a characteristic is, is
00002902-0000-1000-8000-00805f9b34fb
And to access that, the proper step...
