Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
Hello,
I am writing here because I am trying to change some concrete values from a .hex file in order to vary some BLE and other values. I need this because I need to generate...
Hello,
I downloaded the nRF Blinky app (for Android) here :
github.com/.../Android-nRF-Blinky
I'm looking to modfy the code to have an auto connection. For this, I...
As far as I can tell, the application is set to invalid (settings.bank_0 = BANK_INVALID_APP) after the application has been successfully deleted ( devzone.nordicsemi.com/...
im trying to use nrf_drv_timer_t with timer0 but I get identifier "TIMER0_INSTANCE_INDEX" is undefined error. TIMER0_INSTANCE_INDEX is defined in nrf_drv_config but this file...
Hello,
is the nRF51822 able to function as repeater or range-extender, repeating BLE signals from explicit two BLE devices (with known addresses)?
I know there are specific...
Hi,
we are developing a custom board based on an NRF51822 and for security reasons are using whitelisting.
So far this worked well with different iOS and Android devices...
i try to modify the saadc exemple program by includding pwm , but after including header file in the application , source in driver, and includding target, i get error always...
Hi All, anyone aware of a module certified for BLE v4.2 protocol? It doesn't have to be built on the Nordic chip, I'm interested in any other one too. Many thanks!
Hello,
I am using PCA10028 and sdk12.2. My challenge is nrf51822 resets after it executes the code for the first time.
I am storing few values in flash. After that I am...
I'm following this tutorial for creating a basic custom service using the ble_app_template from sdk 13 github.com/.../custom_ble_service_example
I've filled in the following...
