Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
hi，
i can't find the ID for softdevice_s140
run cmd ： nrfutil pkg generate –help
--sd-req TEXT The SoftDevice requirements. A comma-
separated list of SoftDevice...
Hello,
I´ve got a problem with the primary services discovery when register more than 1 vendor specific UUID.
I´m actually connecting one Cadence Sensor and one Motion...
Hello!
I have problem with DFU bootloader on nRF51822-xxAA.
For first, I made all steps for upload bootloader(erase chip, upload SD s130, upload bootloader).
I used...
Hello, I use nRF51822 based device with s110 softdevice. I noticed that data exchange is different on different connected centrals.
For test I used Windows and Android powered...
Hello,
I have my project up and running using the "nrf51-micro-esb" project. I can successfully set my device to PRX mode and have it receive payloads just fine. Similarly...
Hi,
I have an issue about power consumption with a board nrf52 10040. The consumption should be 100µA but is 500µA. I found an errata about that in ' infocenter.nordicsemi...
We're using nRF52 to read two sensors data: one is an ADC chip using SPI; the other is a PPG sensor using I2C. MCU sampling rate is 250Hz, meaning every 4ms, MCU will poll...
Hi all!
I'm a beginner developer.
I start my work with nrf51822, download examples e.t.c
Now I try to download my code in real PCB with external 16MHz crystal.
Code worked...
-----------------------------EDIT--------------------------------------
I've changed topic name, because not buffer overwrite is the problem.
I need some mechanism for...
I am working on a project for college in which I need to build my own PCB. The code works fine on the Dev Kit but on the PCB, the bluetooth is not showing. I have tried looking...
Hello,
I am using nRF UART v2.0 android app and I have added my custom logic above it. I am using this phone as the central device and nrf52 with sdk 12 as the peripheral...
hi
i am using two dongles.one would be sending sensor data from gpio to other through ble.i need a example code for those two.could you please tell me which example i can...
Due to limited budget, I have to use STLINK/V2 to flash code into nRF51822. I have been through steps of how to setup OpenOCD/STLINK/V2/nRF51822 in Ubuntu. After mass erase...
Hi. I'm using nRF52832, SDK13, S132v4.0.2.
I'm making peripheral device using nRF52832.
And I can see it gets BLE_GATTS_EVT_WRITE event as below when central sends WRITE...
I'm having a difficult time getting my project to link to the nrf_serial module
._build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_serial_read (referred...
