Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello,
I have my project up and running using the "nrf51-micro-esb" project. I can successfully set my device to PRX mode and have it receive payloads just fine. Similarly...
Hi,
I have an issue about power consumption with a board nrf52 10040. The consumption should be 100µA but is 500µA. I found an errata about that in ' infocenter.nordicsemi...
We're using nRF52 to read two sensors data: one is an ADC chip using SPI; the other is a PPG sensor using I2C. MCU sampling rate is 250Hz, meaning every 4ms, MCU will poll...
Hi all!
I'm a beginner developer.
I start my work with nrf51822, download examples e.t.c
Now I try to download my code in real PCB with external 16MHz crystal.
Code worked...
-----------------------------EDIT--------------------------------------
I've changed topic name, because not buffer overwrite is the problem.
I need some mechanism for...
I am working on a project for college in which I need to build my own PCB. The code works fine on the Dev Kit but on the PCB, the bluetooth is not showing. I have tried looking...
Hello,
I am using nRF UART v2.0 android app and I have added my custom logic above it. I am using this phone as the central device and nrf52 with sdk 12 as the peripheral...
hi
i am using two dongles.one would be sending sensor data from gpio to other through ble.i need a example code for those two.could you please tell me which example i can...
Due to limited budget, I have to use STLINK/V2 to flash code into nRF51822. I have been through steps of how to setup OpenOCD/STLINK/V2/nRF51822 in Ubuntu. After mass erase...
Hi. I'm using nRF52832, SDK13, S132v4.0.2.
I'm making peripheral device using nRF52832.
And I can see it gets BLE_GATTS_EVT_WRITE event as below when central sends WRITE...
I'm having a difficult time getting my project to link to the nrf_serial module
._build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_serial_read (referred...
Hi
From my understanding of the softdevice API, the maximum packet length is set using sd_ble_opt_set(BLE_GAP_OPT_EXT_LEN, &opt) , but the actual change to the packet length...
Hello,
I would like to build a sensor array that communicate with one master in a star topology.
I have played with the Gazelle protocol example ( gzll_ack_payload examples...
Hi,
I am working on a project where I have 4 advertising beacons which will have to trigger some functions in the central side when it gets the advertising data.
Now I...
Hi Nordic,
During DFU tests i had weird issue. If i compileed bootloader using your makefile everything works fine, instead of compiling with Eclipse IDE.
With Eclipse i...
