I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Currently using nordic52832 to develop products that use batteries.
We found that the problem is that when the BLE module is connected successfully, it takes 200ms to send...
Hi all!
I am developing an nRF52 application that uses RTC interrupt to measure an ADC value every 100 ms. Depending on the measured value the chip shall either go back...
I am using nRF 52 development board. Using Keil to program it. Its has 4 buttons. We can easily detect when a button is pressed, but is there a way to know for how much time...
I'm using the following code to make the beacon sleep:
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
uint32_t err_code;
switch (p_ble_evt->header.evt_id)
{
case...
Hi, Developer Zone!
Can pm_peer_rank_highest function return NRF_ERROR_STORAGE_FULL code?
There is no this error code in description for function, but in the code I see...
Hi
I am sending my BT module with nRF51822 for some regulation test and the Test Lab is using Anritsu MT8852B to communicate with my module through USB-to-UART adaptor and...
Hi team,
I have seen the example of crypto in the SDK_12.3.0. I want to learnt it. But I don't know how to use it, because there is not keil project file, and I hadn't...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello,
I have adapted the ble_app_uart_c project for a custom board based on nrf52832. The application already works fine, however, my peripheral is sending four packets...
Hi,
I decided to use nRFUART Example which is inside of the Master Emulator.
I am using nrf51 dongle for connecting peripheral devices.
When I run the nRFUART Example...
Hi,
I am porting my code from SR3 v1.0 to SR3 v1.1 now.
I have a problem in debugging SR3 v1.1.
In SR3 v1.0, it's fine in MDK-ARM debug session. I can set break point...
I have been working on integrating FDS into an SDK13 project using SES v3.24.
I'm not sure if the memory allocations are set correct. If I increase the FDS_VIRTUAL_PAGES...
So I have been integrating FDS into a project under SDK13. It's based on an example that Hung updated for SDK12.1. So after init of fds the method fds_test_find_and_delete...
This crystal, which is used the nRF52 dev boards and reference designs, is now "not recommended for new designs". I could find another crystal that meets the spec, but just...
Hi,
i'm currently try to figure out how to use an Android device as an IPv6 Server through BLe sending UDP packages. One of my collegues tried this example as it was discribed...
