Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Hello:
i'v try v2.0.2 and v3.0.0 and v3.0.2. got error as follow:
or
sometime install toolchain got msg " Failed to fetch available toolchains. "
what the url...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
So I am trying to figure out what i do and dont have access to as far as flash and ram is concerned. From the nRF51822 spec it discusses this in general but im finding myself...
Hi
My name is Bernard Britton from Trinidad & Tobago and I am looking for someone competent with nRF9E5 to develope a wireless potentiometer position sensor with LCD receiver...
Hi,
While the softdevice is active (nRF51822) available interrupt priorities are:
typedef enum {
NRF_APP_PRIORITY_HIGH = 1,
NRF_APP_PRIORITY_LOW = 3
} nrf_app_irq_priority_t;...
Hi all,
I'm trying to use NRF24L01, using REUSE_TX_PL command,
the data sheet says as long as CE keep high, the chip will transmit the payload continuously, what i wondering...
Hi
Did you have tested the power current of nRF24LU1 when RF was off and USB worked normally?
We want it less than 4mA. Could you have any idea to make it? Thanks.
Hello! I am trying to develop on the nRF51822 eval board as called PCA10001. The programming interface I use is uVision4 on win7.
I would set a static PASSKEY for the pairing...
When I successfully bond with an Android device, then disconnect the Android device, the following attempt to re-connect fails. It appears the chip enters some internal error...
Hi,
after i get eclipse to debug (thanks to cocoa) i need to make a new project. What option i have to choose, to create a new project to run it on my nrf51822 evalboard...
In the nRF51 reference manual, page 59 shows the config value for pullup is 2 (upshift by 2)
In the file nrf51.bitfields.h, at line 2339, we have:
#define GPIO_PIN_CNF_PULL_Pullup...
Hi,
I'd like to add some custom data (25 octets) to the nRF8002 advertisement packets, using the vendor specific data type (FF).
Is this possible in some way or do we...
Hi, I am trying to enabling a notification of an attribute(once the attribute changed, the server will push the new value to the client) and I learned I have to first configure...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I download uart sample from Nordic developer zone . at devzone.nordicsemi.com/.../is-there-a-serial-port-profile-for-ble
Because you had build the uart profile and iOS...
