Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello Everyone
i have J link for ARM processor from IAR 2008 module version 6 which specify support for swd, As I checked it on IAR website it support CORTEX-M0 processor...
I use pin SDIN, SCLK, CS, DC.
but how do I connect the pin nrf51822
spi_master_example is
#define SPIM0_SCK_PIN 25u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN...
I have been reading about code regions in the nrf reference manual and understood about CLENR0 and how to use it. I have however, two questions
What is Pre Programmed...
I am using the SPI Slave port in the nRF51822 and am always transferring 20 bytes. No matter what I do, it seems that the status register in the IRQ says that I got a TX buffer...
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I need to be able to communicate between two boards via UART. I had a look at the example from Ole provided here: devzone.nordicsemi.com/.../ as well as other references...
Hello,
I am wondering if I can use any 128 bit UUID value.
For example, in the example uart project, Nordic UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E is used...
If I want to stream samples up to the nRF Toolbox HRM iOS app plot, what is the fastest that I can call ble_hrs_heart_rate_measurement_send in firmware assuming I have nothing...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...