I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
From what I am reading in the S110 spec, this service is supported but not adopted (i.e. example code. Is this correct? Has anyone implemented a navigation and location service...
Hi all
My hardware is nRF51822 PCA0000 and PCA0001,
I just want to compile/load any UART example to test my UART workable or not.
So I have tried example project button_radio_example...
Hello,
Having a problem with the 1 wire sensor DS1820, I've created my own 1 wire protocol functions. They compiled without any errors. but when I run my program, it only...
Hi,
I'm currently developing a board that utilizes a NRF51822 and I'd like to utilize the meander antenna from the PCA10000 dongle reference design. However, I'm using Eagle...
dear Nordic:
i created a new characteristic assigned UUID 0x18e1.in order to be writable,i set its properties with following in
static uint32_t pressure_high_byte_char_add...
I'm measuring current consumption on nRF51822, making code changes and then flashing/debugging via JLink GDBServer and gdb.
Right now it seems like I either have to physically...
Hi,
I´m using nRF51822 with my own application and I want to connect just to one specific master device (for example smartphone) after this one is bonded:
nRF51822...
Hi There,
I am developing a desktop applications (C#) using NRF2739 dongle and NRF8001 on the other side. Things were going very well using the masterEmulator.dll provided...
Hi,
How to put nrf51822 in power off mode? i simply tried NRF_POWER->SYSTEMOFF = 1; in keil but it is not going to off mode. Is there any procedure before making SYSTEMOFF...
Hello, I am using the HTS example for the nrf51822.
In the example, bond information can be deleted during initialisation by holding down one of the buttons.
In my program...
Hi sir
In Desktop 2, before BTLE pairing, nRF51 uses Connectable Indirected advertising. After BTLE pairing with BTLE host, nRF51 will select Directed advertsing for saving...
Hi to all, my first experiments with NRF51822... i compile the example projects, and everything works fine (compiling and download are ok), but looking at the code editor...
Hello,
I am using an nRF51822 Development Kit. I am trying to run pca10001/board/uart_example (with simple_uart) using the UART serial viewer built into the Keil programming...
