Hello dear fellow developers,
I am solving the problem of how to add another peripheral to the project.
I would like to know a universal procedure for adding any peripheral...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
I use softdevice 6.00, size is 80K Byte. I use the chip NRF51822ab,and configurat the irom start at 0x14000,size 0xC000, IRAM, start at 0x20002000,size is 0x2000 ,in keil...
Hi,
Is there a possibility to read the state of the gpiote pin? (is it high or low). Is there any function or any other way to do that?
I'm changing the gpiote pin via...
Hi,
I made a own service for a rotary dail in a peripheral(S110). This service send the speed, direction and a counter (all uint8) of de rotarydail in separate characteristics...
Hi Everyone ,
We were using nrf51822 rev1 IC for our project and now it is changed to nrf51822 rev3 . Previously we were able to detect the chip in nRfgo Studio on our...
I am looking for a device with support for the 4.2, long packets (up to 255 bytes) feature. I see that the nRF52 is a 4.2 device. But for what I understand the optional long...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
My goal is to capture on gpio burst infrared proprietary "messages" composed of multiple "bits".
The Length of each bit is around 100 to 200us.
Initially I planned...
(I understand my question is similar to devzone.nordicsemi.com/.../ , but I would like some additional clarification not provided in that post.)
Hello, I've been developing...
On a BLE_GAP_EVT_CONNECTED, I'll send some data to an attached microcontroller via UART. The code will expect a response of that data, all while being inside that BLE_GAP_EVT_CONNECTED...
My application involves the Nrf52 using softdevice and a slave only SPI ADC running at approximately 26khz. The ADC has a pin interrupt to indicate data ready. There seems...
Building nrf_delay.c (or anything else including nrf_delay.h ) with NRF52 defined produces:
arm-none-eabi-gcc -I C:\Nordic\nRF5_SDK_11.0.0-2.alpha\components\device -D_DEBUG...
Hi, someone know whi when i press disconnect on iphone the nrf51 restart from the mail?!
Why if i disconnect android device the chip does not restart as the iphone?! is normal...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
