I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
I am trying to send stream of data over BLE. I am using nRF52 development kit and in that ble_app_uart code is running. I want to send continuous data to the UART and...
I am using PPK 1.1.0 to compute current draw on a custom hardware.
If I upload ble_app_hrs example on the nRF52-DK and measure it directly, I obtain average reading as 550...
Dear all,
sorry for asking a very beginner's question but I'm really a beginner and want to understand what I'm doing :)
What I have:
nrf52 DK
nrf SDK11.0.0...
Hello,
we are using the USB CDC ACM Example to set up a USB connection between the computer and the nRF-Chip.
By pressing Press Button 1 a bunch of test data will be sent...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
Hi, Everyone
I am developing based on ble_app_uart at nrf52832 (softdevice s132)
I modified the program slightly.
- After the connection is confirmed
- Send 100 bytes...
Hi Devzone:
I have build up a environment that are
1. a thingy52 with mesh-briadge
2. a thingy52 with mesh-node, which is control by segger-debugger, and it shows
...
Hi everyone,
On my actual configuration I can connect one smartwatch to the nRF51422, and re-connect it later if the communication have been interrupt.
However when I...
Hi Everyone,
I've looked around at the Nordic documentation before asking this question but can't find any good example. I am looking for an example to create a repetitive...
hi
I need to set a pin high when i make a connection to the device .so i set to output direction in main.c file.i have include gpio.h and nrf_delay.h file in main file ...
I'm using the nRF52382 with SDK 14.0 and softdevice s132 5.0.0, and I need to send up to hundreds or thousands of kilobytes to an Android phone over BLE. I need to optimize...
