I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
Hi everybody
Can nrf51822 advertise with a Balun whose SE pin is disconnected? (not connected to antenna, just left disconnected)
Just like the reference circuitry above...
Hello,
I can see, that sd_ble_gatts_hvx() returns 13313, if the notification is not enabled for that characteristic from the connected central. --> S120 Softdevice runs...
Hi
I got my new NRF51 DK. I was able to test it with blinky using mbed. I had to add the add the device nRF51-DK. then compile it and drag the .hex file into the mbed drive...
When I first got the nRF51-DK board... I was able to see this board on nRFgo. I then added the s130 hex file to it.. Since then when I connect this board, it does not show...
Hi,
Everyone,
I am trying to achieve minimum current level, I can possibly achieve, with continuous BLE transmission
so, I tried running BLE_POWER_PROFILING_APP given...
Hello to everybody.
I've buy a nrf51822 module with a motherboard.
i struggling to programming an uart over bluetooth example but i think something missing.
With nrfgo...
We configured nrf24LE1 as PRX and nrf52 as PTX and the packet sent out every seconds.
The nrf24LE1 will only received the packets every twice packet sent out and both packet...
I tried to use difference Data Rate for testing the transmit distance. Don't know why using the 250k bit is worse than using the 2M bit & 1M bit. The distance will decrease...
I am debugging a small program for the nRF52, which uses the App Timer and communicates over UART. I am trying to keep up with bug fixes, and so I'm using SDK 11.0.
The...
We have an application that requires a fairly quick disconnect (under 250msec) when the RSSI exceeds a threshold, for example -80db. Unfortunately, around 1 out of every 4...
I am trying to program a nrf51822 module using the nrf51-dk.I have made connections as per the nrf51-dk user guide, but sme is not working...
I am using the Vdd of the...
Hello all,
In a network of sensors with power constraints in a room which protocol is the best?
Newer devices seem to use BLE but I don't want to discard good old nrf24l01...
