Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
What is the proper way to use the Queue Library and define a queue that can be used across multiple C files? I have the following code a my common header
NRF_QUEUE_DEF(uint8_t...
Hi all the Nordic friends and Team,
I would like to do a Batch OTA of one hundred devices right now... I'm on the NRF52 stack for my devices to be flashed. And I'm using...
I test SoftDevice V6.0.0 on nrf52832(BLENANO2) I run 1. sd_ble_gap_scan_start() 1000ms/100ms/10ms scan_window/scan_interval 2. sd_ble_gap_adv_start() 1000ms interval result...
When my mobile phone reads my characteristic, I would like the characteristic to be calculated at the same time, and not before. i.e. like a video game that does not render...
Hello Supporter,
I am Using NRF51822 QFAC .
My probleme after uploading DFU ,SOFTDEVICE AND APPLICATION .device always in DFU mode and also when try to upload new application...
Hello Supporter,
I have NRF51822 QFAC having 256kb ROM,32kb RAM.
now i want to upload all three things DFU,SOFTDEVICE,and APPLICATION .when i upload SOFTDEVICE and APPLUICATION...
Getting ready to go into production with our custom nRF52832 board, we need the board to start running our application immediately after being flashed. Using:
nrfjprog version...
Hi all,
I want to add 5 characteristic to my custom service . But when I add 2 characteristic , it worked fine . When I add 3 characteristic ,In funtion sd_ble_gatts_characteristic_add...
Hi,
I am trying to read data from a temperature sensor, but i'm stuck at the twi read operation. i have already interfaced the sensor with esp32 and is working fine. please...
Hi,
I have a really really dumb question but I will ask ...
Is there any impact regarding the orientation of an IFA antenna?
Everywhere, in all examples, we can see...
Hello everyone,
I'm trying to implement the bootloader from SDK v14.2 on the nRF52840, SD v5.0.0 s132 (using our board and app).
For my testing, I erase the whole flash...
Hi Forum,
i've started the development of an custom service on a nrf51822 with s110.
The Service contains 4 Characteristics where notifications are enabled.
At the...
I have a custom dongle that connects to the PC through a USB-UART chip. It is based on the nRF51822. I have another board based on the nRF52832. This board needs to be able...
Hi,
I am building a device to act as an iBeacon, with other services layered on top. This is based on a Raspberry Pi with a Class 1 USB Bluetooth dongle.
I need to be...
Hi everyone, I'm working on the nrf51822 QFAAH I tried to flash the ble_app_uart example and it didn't work. So I debug it and it stops here
As you can see in the picture...
