Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi
currently I am working with the nRF52840 Preview DK. Using the on-board J-Link interface I can send debug messages to the debug console of the Segger Embedded Studio...
Hi,
I have tested AES-CCM of nRF52832 with reference to the following answered questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Dear all,
I did below steps to connect to the BluFruit Feather board via STLink V2:
1) Install OpenOcd and STLink USB driver as: https://pcbreflux.blogspot.com/2016...
I have some code originally working using SDK 13. It reads data from the UART and send it out in scan responses. iOS was able to capture the scan response data successfully...
hi all,
Our application is a peripheral device with sensor data that is sending up to 540kb/s (68kB/s) to the central device (data rate could probably be reduced if necessary...
Hi,
I'm trying to take the readings of temperature and humidity from 4 Nordic Thingy:52 sensors by using mesh. I did the connection of the mesh and I can control the nodes...
Hello,
I am new to BLE so I am not sure where to start. I have two nRF52832 chips, one will receive data from an FPGA through SPI and then I want to send the data to the...
For reference, in case anyone else gets a similar issue :
Using the SES import facility to import a Keil MDK v5.25 Project.
After fixing a couple of other import errors...
Hi @ll,
I'm not able to receive any ble events that should be triggered by the SoftDevice.
What I did: - Using dfu_example (added beaconing advertiser and connectable...
hi,
I use SR3 52 V1.2 for development, and I want to copy a new project to change some code.
When I changed the file name, I found it could not be compiled through, only...
Hi all,
We are currently developing a wireless system for a musical instrument and MIDI controller based on a nRF52832 (using Laird BL652 modules). Our requirements prevents...
Hi,
I would like to test the ZigBee throughput like the examples ("ATT_MTU Throughput Example" for BLE and "Thread Throughput Measurement Application").
I'm not familiar...
Dear Support,
I am working with the new SDK 15, and got some question about using whitelist without device manager, and without pairing or bonding. As stated here: https...
I'm using v14 of the SDK and I cannot for the life of me get either the external 32MHz or 32.768kHz clocks working.
How is this possible using the SDK?
