Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
Hi all,
getting burnt out from searching the fourms and finding dead ends or outdated answers so just posting a question quickly.
Somewhere along the line my nrf51DK has...
I am working on a product based on the nRF52832 (using the Rigado BMD-300 module) which is basically a data logger with a BLE connection for offload. I am running FreeRTOS...
Hello,
We have a custom board based on nRF52832.
there is 1 LED on P0.29:
#define LED_1 29
First I initialize the GPIO:
nrf_gpio_cfg_output(LED_1); // this lights...
When I complie this SDK using keil5, I got this error "Error #544: Required Software Pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.16.0' is not installed'" How can I get...
red-contrib-nordic-thingy
Always getting "no thingy found" error from node-red in ubuntu. But i am able to use gatttool and able to get notifications from thingy on button...
I've noticed following line in SDK14.1 release notes:
`
Fixed a bug where nrf_log could crash when heavily loaded.
`
I'm using SDK13.1 in my current project...
I've recently jumped to nrf5 sdk v15.0 from v12.3 and met a problem in setting up a custom ble service. Actually the service itself is visible via nrfConnect andorid app,...
Hi,
How can I know the value of the interval and scan window for an nRF51 dongle? Is there any way to change these values? W hat is the valid range for both parameters ...