Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Log-2018-01-12-11-49.txt When I use the nrf connect app to connect my device, it often does not connect to my device.And i see the error on the log is： ERROR 22 GATT_CONN_TERMINATE_LOCAL_HOST...
I have learned that the "sd_power_dcdc_mode_set ()" function does the appropriate mode switch.(LDO and DCDC)
I learned from the following URL.
devzone.nordicsemi.com...
Hi to everyone!
It's the first time I use and program clocks in a device. I'm very lost with crystals, power management and this stuff.
I have a custom board with two...
I am trying to flash custom firmware to Thingy using nrf52dk and nrfgostudio.
I have attached a cable from the debug out port on the DK to Thingy, and followed the steps...
Hello,
I'm using the nRF51822 QFAA and I just came out to this problem:
Is this still unsolved? I always end up in the same forum threads and making 0 progress on how...
About the PCB antenna layout of nRF52810, can i directly copy the reference layout provided by Nordic and paste it on my PCB?
Below PCB layout photo, is i directly copied...
I am about to start using the nRF52 for several projects and would like to know which version of Eclipse is recommended? Since Eclipse can be customized in many ways I'm looking...
i took the original sdk 14.2.0 s132-5.0 ble-uart nus-service example for reference measurements to send data from a 52832 to an android device running nrf uart v2.0
to...
I need to add two more led pins - #10 and #30 - to that board, but I don't know what to do with LED_START and LED_STOP lines, and so far, it is difficult for me to trace any...
Hi i am working on ble_peripheral example on nrf52. i am getting issue in bsp.c
BSP_BUTTON_ACTION_LONG_PUSH' undeclared (first use in this function)
bsp_button_event_handler...
main.c Hi,
I have implemented button long press with APP_BUTTON library with APP timer (a 5 seconds timer).
Normally the detection works fine.
But I found that if the...
Hi,
I'm trying to get BLE pairing example to work. I downloaded the missing micro-ecc library and I encountered this problem: github.com/.../70
So I've compiled this...
Hi,
I try to enable the ram retention function. (Bank 4)
So i used the POWER structure
NRF_POWER->RAM[4].POWERSET |= (POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos...
Hi,
We use SDK14.0 with S132 v5.0.0 on a custom board with nRF52832.
In our application using a lot of flash operation, and we found the error PM_EVT_PEER_DATA_UPDATE_FAILED...
Hi,
I am working on the nRF52840 Development Kit and I want to merge between ble_app_uart to usbd_cdc_acm examples.
I opened the usbd_cdc_acm example and added all .c...
