I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hi,
i get the example for using PWM to run and modfied it to use it in my application. My Prolem is that i only have one PWM Output toggle Pin. How can i build a second...
Hi,
I'm using the MCP to send a long to a nrf6310 board loaded with SD v6. The board hangs when I send a long though, is this due to the MCP not being set up to send longs...
Hello,
I have the nRF51822 Evaluation Kit. I have run the basic code examples like 'Blinky' and the BlueTooth HRS (Heart Rate) application, successfully.
Now I would like...
Hi,
Is it possible to give a function address to the "Task End-Point" of a PPI channel?
Like :
err_code = sd_ppi_channel_assign(PPI_CHAN0_TO_TOGGLE_LED,
&(NRF_TIMER1...
I am designing a device that needs to operate both as a Peripheral (such as a Heart Rate sensor) and also as a Central so it can optionally connect and gather data from other...
Hi,
in my application I have a device that has to be controlled by a remote control. For transmitting data between the remote and the device I would like to use BLE (not...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
Hi,
does firmware or example source code exist for the PCA10000 USB dongle that implements the Bluetooth HID host?
I would like to use it as receiver for the Nordic Smart...
Hi all,
I am trying to specify a fixed port for a L2CAP connection on the nRF51822. The client is a Linux box running bluez (which has BLE support). The client software...
Hi,
Just bought the nRF51822 eval kit. Looks like it came with some great demos for iPhone (nRF_Demo_Utility, nRF_Proximity, nRF_Temp, nRF_UART), but having trouble getting...
Hi,
I upgraded to the 4.3 nRF51 last night and am suddenly having a whole slew of issues:
(1) When flashing the EK, the Segger now reports 257K of Flash (maybe it did...
