Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
m_prov_state is getting assigned at line #150 as well, I thing the assignment here is redundant.
I have also created a pull request on GitHub for this. Although this is...
I am trying to use an application timer along with some variables. I am using ble_app_template as base. To start of I've got the timer without any parameters being passed...
Hello,
I'm trying to port my application from the nrf52832 to the nrf52810. I'm using the Fanstel modules, originally was using BT832 and am now trying to bring the application...
1.What are the dimensions of the NFC antenna (component A1) for the reference designs given in the design files here
http://infocenter.nordicsemi.com/pdf/nRF52832-CIAA_Ref_Layout_v1...
Hi,
As showed in the code, I masked " else if (m_nw_state.provisioned_devices == 0) ", then it reported "NRF_ERROR_NOT_SUPPORTED".
Can you tell me how should I do...
Hello,
I didn't manage to run PA/LNA switching with softdevice (function: sd_ble_opt_set(BLE_COMMON_OPT_PA_LNA, &options)) with P1.* GPIO pins.
Note that all P0.* pins...
Hi,
Is there any chance that we can completely turn-off the radio part of nRF52832 and only the application part of the processor running. Also, we should be able to turn...
Hi,
I would like to program and debug a code into the Nordic Thingy:52. I read that I should have either J-Link or nRF52 DK. And I have the nRF52 DK, but I don't know...
Hello all,
I'm working with the nRF51 SoCs, with the s130 SoftDevice and SDK12.1.0
I have a BLE Nano from Red Bear Lab that has a nRF51822 doing adv and it expose...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
