Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
We are developing a React Native mobile application for iOS and Android, making use of the react-native-ble-plx library to interface with the BLE UART service from the examples...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
Hello Supporter,
I'm going to develop one BLE nrf51822 based custom device. in which i want to use BLE DFU.
i am able to load DFU and APPLICATION with KEIL uvison 5. ...
Good morning, I have a question about MESH RF. We need connect many vehicles to station base via RF. - Station base --> UART --> RF Device [ MESH ] (SKY CLEAR and outdoor...
Hello Nordic community! My setup is pca10040, android tablet, s132, sdk14.2.
This time I am trying to understand why this code:
While using nrf toolbox nrf UART prints...
Dear All,
I would like to explore the possibility of repetitively transferring small amount of sensor data from an nRF52832 to an ANT(+) compatible Android device, for a...
We are using an MDBT42V(29 pin) module which we discovered from the datasheet, comes with an nRF52832 controller. We are using a nRF52 DK to dump codes into this target board...
