I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
I am trying to create a custom sensor for CT1711 temperature sensor. I have created the sensor driver code and device tree binding, but it won't start (initialize) and the...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hello,
I’m working with the Matter Light Bulb sample in nRF Connect SDK v3.0.0 , and I’ve run into build issues when enabling certain optional commands in standard clusters...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
I'm using the nRF51822 with the S110 soft device. When specifying the maximum size of a variable length characteristic notify property (the max_len field of the ble_gatts_attr_t...
now,I want to know how the process that application invoke the method to send or recieve the data,but I did't find it in the source code ,and when I want to find the definition...
I want to read a line of text from a UART peripheral. I'm using app_uart.c, not the "simple UART" example code.
My main() looks something like this:
uint8_t line[MAX_CHARS...
Hello,
I've been working on the SPI module for the nRF51822. I used the sample spi .c file as a starting point, but I got rid of the timeout (not sure why there is a timeout...
Hi,
We have nrf51822 evaluation kit and some custom board with nrf51822 chipset(works fine). And also we have tested the nrftoolbox application with the proximity service...
I use the example "Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\led_radio_example" and "Keil\ARM\Device\Nordic\nrf51822\Board\pca10000\led_radio_example" to communicates...
Hello, I think there's a mistake in page 35 of the specification, it says that if Auto Retransmit is disabled (that meaning Auto Retransmit Count = 0 in SETUP_RETR register...
Hi all,
I am using an nRF51822 Development Kit and I would like to create a simple test code that allows me to send data (no matter what kind of data, also a sequence of...
Hello, I am working with both QFABA0 devices as well as a QFAAC0. Because of the outdated silicon I am constrained to SDK V4.x and SD V5.x
My current test setup is
I...
Hello,
which profiles are available currently to the S120 protocol stack? In the nRF518 SDK V5.1.0 I could find only one example profile for Heart Rate. However, this is...
HI,
I am the beginner of develop bluetooth le device, and test the sdk 4.x examples and it's work correctly,
then i updated the sdk to 5 , but i can't get the example...
Hello,
I am Ethera's engineer, evaluation technologies to include on our next generation products.
Here our goal is to have a transparent mode between a smartphone program...
Hi There,
I want the functionality of my device to change when a value is written to a gatt characteristic. I've written an event handler that gets called whenever a write...
Hi,
I have Keil 5.1, SDK 4.4.2, SD 5.2.1, PCA10001 from EK v2.0.0 and I am trying to make SPI example from nRF6310 work.
I have changed below lines as:
#define ERROR_PIN_SPI0...
