void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
This is just a quick check of my understanding of the interrupt priority levels on nRF51. I read up on the documentation I can find.
I'm assuming that I will receive...
Hi,
I am designing a custom PCB with the nRF52832, I am going to use wire bent antenna over it. Can I bend feed wire by 45 degree. I have attached image for the part I am...
Hi All
I am using the example of uart in SDK10 wit nordic 51822
First of all ,I add a PA with 51822 to increase the signal of BLE, but I notice that the speed of PA is...
I can read peer address and rssi field in the scan request report. But how can I read the AdvA address field in the scan request to make sure that the scan request packet...
Is there a method to remove a node from the network using the current bt mesh stack? I've looked through device_state_manager.c but it appears to me that there are only functions...
Hi,
I am using 2 nRF52840 DK to build a network, One is the client and the other one is the server. Both of them are connected to computer with USB cable.
I would like...
hi,
i test my project for i2c sensor module, the debug found have error what there are the following error tips.
..\..\..\swct_application\i2c_sensor_driver.c(14): error...
Hi,
I'm trying to write custom boot loader, that receiving hex file via uart and write it to location 0x40000 and then jumps to the location. I changed FLASH_ADDRESS and...
Dear experts,
We are evaluating to perform Round Trip Time (RTT) measurement for ranging application. The accuracy requirement is 1m to 2m. Are there any sample applications...
Hi,
I am using a custom board which I designed based on the Puck-js board, except that I am only using an I2C based distance sensor instead of the other devices onboard...
After experiencing UART problems without handshaking I opted to enable hardware handshaking.
Where RTS & CTS are pins 5 & 7 respectively.
I was experiencing overrun (insufficient...
The nRF6905 nRFready Basic Remote is a complete hardware and software reference design for basic 2.4GHz RF remote controls.
What nRF24LE1 devices are included in the hardware...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
Hello,
I would like to use nRF52840 in order to make some BLE5.0 mesh products. When I open the nrF5 for mesh, I can see only examples for nRF52832.
Do you know if these...
hello, i am trying to implement external RTC in my application. i am using the SDK 14.2.0 and softdevice s132 .n also for external RTC using the M41T62 with nrf52832DK. so...
