I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi all
We are experiencing high current draws that lead to 51822 chip failure under some circumstances. By looking at this thread
https://devzone.nordicsemi.com/f/nordic...
Hello there,
I am developing a coap based client-server application which has thread mesh network. Client is a sleepy node here.
Dev kit: nrf52840
Thread SDK: nRF5_SDK_for_Thread_v0...
Hello everybody,
I want to see integer number with use NRF_LOG_INFO . I try to this;
But RTT_Viewer show like this;
"You have 536881776 trial rights."
I have to...
I am using Nordic NRF528321 with SDK 11.0 and soft device S132 as ble central.At peripheral side it is Nordic NRF51422 with SDK12.2 and soft device S130.I am trying to pair...
Hi,
I'm on nrf52dk platform.
I have flashed the MQTT publisher firmware in IOT section provided in nRF5 SDK 14.2, config the ip address and auth info in code; established...
Hello, I am using nrf52840 PDK, sdk 13.0.0. I managed to read accel, gyro data from the MPU9250 using MPU library based on this example . However, I got magnetometer reading...
Hi guys,
I start with SDK13 and i want to create SDcard saver same information every 5 second on card. This is my code, i have no idea why it din't work.
I red that...
Hi,
i am trying to compile nrf51_sdk example using linux
I have 1- gcc-arm-none-eabi-4.9-2015q3 in location /usr/local/gcc/gcc-arm-none-eabi-4.9-2015q3
also install...
Hi there,
How in the question title, what could be more efficient? use a nrf_delay_us or Timer with HFCLK source.
I am creating a custom protocol to transfer data between...
Hi, is it now possible to flash (via DFU OTA) a nRF51X without the nRF Dongle, but with a generic BLE dongle on Windows 10 ? Thank you for your answers.
Hello,
I am using Nordic's iOS library to perform DFU in our app to upgrade firmware on some BLE devices. Before the DFU, the app scans it as "Paradevice", but reads it as...
Hi,
I'm designing a prototype board with the nRF52832-CIAA and was planning on using the Johanson 2450FM07A0035T integrated 2.4 GHz filter, but have not been able to find...
Hi
in pcb designing of the nrf52832 we use two oscillators one is 32 MHz and another one is 32 kHz.
can't we use both 32 kHz instead of one 32 MHz for saving power consumption...
