I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
nrf52832
SDK 14.2
My application is locking up, and finding the cause is proving to be difficult. I've enabled DEBUG and DEBUG_NRF and included the hardfault library...
I have an application that requires talking to 21 sensors wirelessly. The bandwidth required by each sensor is relatively small - roughly 2KB/sec. The sensors need to talk...
Hello,
The mesh lightswitch on/off example only calls 'sd_app_evt_wait' in the main loop.
I'd like to use '__WFI' instead. (Im combining some code with mesh, and i'd like...
Hello,
This case is a part of a private case. Unfortunately havent responded for few days. I believe he has days off or something, therefore I am willing to receive help...
Hi everyone,
I design own boar with nRF52810 SoC. But i dont know how to programming external. Which pins are using programming? SWDIO and SWCLK pins using programin i know...
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Written a custom script to write product model no into UICR Registers. After updating Model No, DFU was getting failed at state 6 i.e after updating init data after moving...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
I am trying to sent multiple messages from nrf52dk but it seems that i can sent only 7 even if i put a delay between messages . Any suggestions ?
for(int x =0;x < numberofevents;x...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
I used two PCA10040 boards to test the UART serialization function with s332 softdevice.
I add my ANT_PLUS_NETWORK_KEY and build the examples "experimental_ant_ble" is working...
Hi, I have a strange problem. I am new to nRF IC's.
I recently took a new job...the person who wrote the code for our nRF51422 lost some source code in the process of changing...
I'm trying to create a HID bluetooth device with multiple connections to centrals. Looking at the ble_hids service implementation, the on_connect event handler sets the connection...
