I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Does anybody has TWI for SDK7 and SD110?
I have problem with twi. Only HardFault appears.
I tried twi_sw_master and twi_hw_master
I would like communicate with senzor...
I have included app_fifo files in the group as well as in the linker along with enabled APP_UART in Configuration wizard of sdk_config.h still the error persists. Please ...
I've been trying to find resources on the possibility of securely limiting BLE connections to only 'signed' applications. I understand that this goes against the general concepts...
Hi all , I using timer 0 to count from 0 to max value 32bit . In my code :
If I using NRF_TIMER0->TASKS_CAPTURE[1] = 1; for save counter value to CC register . It run...
Hi Everyone
I am working on nrf52832 with sdk 14.0.0 on iar IDE. TWI and SPI separately working fine in buttonless_dfu then i merged SPI and TWI in buttonless_dfu itself...
I am trying to update an older application use the spi_5W_master and receive the error: (SDK11, using S210 softdevice)
:RTE\nRF_Drivers\nRF51422_xxAC\spi_5W_master.c(346...
Hi,
I'm trying to advertise 2 packets simultaneously, connectable packet using the soft device and a becon packet using the timeslot. I'm using nrf52 SDK 14.0.0 and SD132...
Hi I am doing some research for my paper, but It is my first time to use NORDIC board.
With broadcom and bluez combination, I could check data packet in l2cap layer, but...
Hi All,
I have a question about NRF52840 power consumption. It is not very clear from the datasheet what is the power consumption if I'd like to use only one of the DC...
Hi everyone,
Preface: I'm an educator and my students are familiar with the Arduino IDE, so I'm using that in combination with the sandeepmistry/arduino-nRF5 core.
Our...
Hi
I am developing nRF52832 wake up solution using LF (Low Frequency).
Initially, I develope it without sd_app_evt_wait .
After that, I am used sd_app_evt_wait to reduce...
Hi, I'm writing this because of nRF52840 booting error
I got this product today and It worked well, but after I downloaded one of the example's ~DEBUG.jlink file to the...
I may have a massive misunderstanding here....
Using nRF52, SDK 14.2, Ant S212.
I use a background scan to discover devices on channel 0, with a beacon on channel 1. ...
My isp (Internet Service Provider) doesn't provide ipv6. Now how do I send ipv6 packets (BLE over ipv6 packets).
Updated: I have an Nrf 52832 and I want to send access my...
