I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Dear Developer Zone,
I am using nRF51822 with softdevice.
Small question about device reset : To reset the chip, do I need to do NVIC_SystemReset() or sd_nvic_SystemReset...
Hello,I'm porting a freeRTOS project to nrf51822 QFAA with 256k flash and 16k ram. I want to use s130 2.0 sd.
Previously this project was done with s110 sd and everything...
Hello All,
Please find the attached schematic , please review the same and give your valuable feed back , we are using NFC functionality in the same . earliest reply will...
Hi, We have an application with 1 central and multiple (6-7) peripherals. The peripheral is running a custom service and the central is running a custom (central) service...
I try to run UART/Serial Port Emulation over BLE on SDK v14.2.0 with nRF52 DK and nRF Connect on Android phone following link " http://infocenter.nordicsemi.com/index.jsp...
I am trying to run the coap ipv6 based example code provided in nRF51 IOT SDK. I am using my Linux PC along with a BLE adapter as a BLE enabled router. I can successfully...
I came across this a while ago, however it gives no indication as what releases, of Segger J-Link suite, each nordic J-Link OB download has been tested with.
Is there page...
Hello, I am looking for documentation on the Mesh DFU Protocol. It looks like it is the same DFU that the mesh branch of the nrfutil python app is using. I would like to do...
Hi,
I tried to use fs_erase and fs_store functions but they both return the value FS_ERR_INVALID_CFG which means "Invalid fstorage configuration". I'm working on nrf51822...
Hi,
I'm using SDK 14. I started from ble_uart application, and to use ADC as well I ported ble_app_uart__saadc_timer_driven__scan_mode (SDK 13) to SDK 14 (made changes in...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
