I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
I am using nrf5340 audio DK,
The project I use is v3.0.2 .\samples\nrf5340\empty_app_core\. If the board target is nrf5340 audio DK
a compilation error will occur. build...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
I'd like to use the SBOM tool to generate a list of licenses used in my build.
I've been following the instructions here: Software Bill of Materials
In order to run...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I'm using a nRF52840 configured as Central and Peripheral, with nRF5_SDK 17.1.0 (I'm Not using Zephyr) for reading the Device Name from the Generic Service of a beacon. I...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
So i purchased the thingy 91 eval board to try it out and see if it will be easy to work with.
I was able to follow the instructions and get vs code working properly and...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
