Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Does anybody has TWI for SDK7 and SD110?
I have problem with twi. Only HardFault appears.
I tried twi_sw_master and twi_hw_master
I would like communicate with senzor...
I have included app_fifo files in the group as well as in the linker along with enabled APP_UART in Configuration wizard of sdk_config.h still the error persists. Please ...
I've been trying to find resources on the possibility of securely limiting BLE connections to only 'signed' applications. I understand that this goes against the general concepts...
Hi all , I using timer 0 to count from 0 to max value 32bit . In my code :
If I using NRF_TIMER0->TASKS_CAPTURE[1] = 1; for save counter value to CC register . It run...
Hi Everyone
I am working on nrf52832 with sdk 14.0.0 on iar IDE. TWI and SPI separately working fine in buttonless_dfu then i merged SPI and TWI in buttonless_dfu itself...
I am trying to update an older application use the spi_5W_master and receive the error: (SDK11, using S210 softdevice)
:RTE\nRF_Drivers\nRF51422_xxAC\spi_5W_master.c(346...
Hi,
I'm trying to advertise 2 packets simultaneously, connectable packet using the soft device and a becon packet using the timeslot. I'm using nrf52 SDK 14.0.0 and SD132...
Hi I am doing some research for my paper, but It is my first time to use NORDIC board.
With broadcom and bluez combination, I could check data packet in l2cap layer, but...
Hi All,
I have a question about NRF52840 power consumption. It is not very clear from the datasheet what is the power consumption if I'd like to use only one of the DC...
Hi everyone,
Preface: I'm an educator and my students are familiar with the Arduino IDE, so I'm using that in combination with the sandeepmistry/arduino-nRF5 core.
Our...
Hi
I am developing nRF52832 wake up solution using LF (Low Frequency).
Initially, I develope it without sd_app_evt_wait .
After that, I am used sd_app_evt_wait to reduce...
Hi, I'm writing this because of nRF52840 booting error
I got this product today and It worked well, but after I downloaded one of the example's ~DEBUG.jlink file to the...
I may have a massive misunderstanding here....
Using nRF52, SDK 14.2, Ant S212.
I use a background scan to discover devices on channel 0, with a beacon on channel 1. ...
My isp (Internet Service Provider) doesn't provide ipv6. Now how do I send ipv6 packets (BLE over ipv6 packets).
Updated: I have an Nrf 52832 and I want to send access my...