Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
My goal to build a device that can connect to phone with nRF8001.
I am using nRf8001 Development kit. My prototype uses TI msp430 with the nRF270 board in the kit, and I...
Hello,
I am using a Windows 7 VM (VirtualBox). I can flash my NRF51 DK using nRF Go Studio just fine.
When I open the Master Control Panel (3.10.0.14), I can see the device...
Where can I find a description of the different nRF24 part numbers? Specifically, I am interested in learning which part numbers correspond to OTP variants. Thanks!
Hi guys, I have an application, where I need to change the role of the S120 softdevice on demand. So, the application boots into central role, reads a couple of BLE sensors...
I am using a photo detector to sense heart beat data. That sensor data is being sent to my nRF51 DK's ADC and then transmitted out via Bluetooth. I want to collect that data...
I'm using nrf51-ble-driver_win_0.4.1 to connect BLE devices on PC. When device has a 128bits UUID, you have to call sd_ble_uuid_vs_add( &uuid128, &p_type ) to register the...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
i tested coap-server example. it works well.
i will test mqtt-subscriber example.
my question is...
Sometimes the service discovery procedure in Android will discover all services but not the characteristics included in them. So all services will be empty. If I then open...
The nRF51 SDK (version 9) documentation tells to activate SPI using the SPI_MASTER_0_ENABLE and SPI_MASTER_1_ENABLE macros. Where should these definitions be made? Other components...
Dear all, after solution of some compilation errors on github nrf51_ble_app_lbs_master for SDK 8.0.0, I tried flash application using nRFgo Studio, it says that application...
Hi,
I am using the sample ble glucose code provided in the SDK.
When i am trying to connect it over BLE interface through Master COntrol Panel or iPhone app it asks for...
I haven't updated my copies of the nRF tools, or mBed's nRF51 code for some time. I just did and now it seems my old method of flashing no longer works. I was doing something...
Hi all,
I've developed a firmware solution for one of my clients. I've compiled using Keil, testing it on a board which previously had SD110. Then I delivered .hex file...
