Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello -
I'm not having any success using my PCA10024 as a dongle for MCP. Here is what I'm doing so far....
Remove PCA10024 jumper from P0.30-GND.
Connect PCA10024...
Greetings,
I am trying to minimize my BOM line items. Can C10 decoupling capacitor stated as 47nF/X5R on the reference design be replaced with 100nF/X5R without consequence...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi,
I modified the uart_example project for the pca10001 board of the nRF51822 evaluation kit to make it work with a UART TTL JPEG camera. So far, the camera can receive...
Hi,
There was a thread about using PAs (and not LNAs) with the nRF51 a while back with some good advice.
One question I still have: is there currently any way to support...
The nRF51 Series Reference Manual v3.0 notes the potential need to set the OVERRIDEx registers in the radio mode to values from FICR.BLE_1MBIT to meet deviation requirements...
hi, i am working on a project which needs a relatively accurate high frquency clock. when i ran my program without softdevice, the HF clock's accurency could fullfil our requirement...
I'm trying to update the 51822 beacon example to work with iOS8 (iBeacon).
So far, I have registered to get iBeacon license from Apple, and setup the tools for compilation...
As the title states.
The DFU controller for OTA updating of the nrf series is described in the documentation of SDK 6.0. It is possible to flash the nordic USB dongle with...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello -
I'd like to make sure my RAM/ROM layout for the nRF51822_XXACis OK - if someone has a minute to double-check it that'd be great.
I started with the "nRF51822 Beacon...
Has anyone been able to get the examples to work on PCA10028?
I went through the following steps:
Used nRFgo Studio to flash in s110_nrf51822_7.1.0_softdevice.hex
Downloaded...
Hi,
Could I write or update flash without softdevice ?
Due to I must update softdevice on our product, but it doesn't have any JTAG Interface,
so, I want to use our application...
Hi,
I want to start TIMER1 by a GPIO_TE.
When the program enter the TIMER1_IRQHandler(), I want to disable the ppi.
And when the program leave the TIMER1_IRQHandler(),...
