Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I am trying to use the nrf51822 to send media button commands over HID. I have seen several questions on here and they usually involve the HID Mouse example (which doesn't...
Hello,
I have been trying to implement AES in order to encrypt a time stamtamp to be sent in the advert of the iBeacon ( 128 bits, using Minor and Major bits, (16+16)*4...
Hi,
I am trying to decrease circuit power consumption that's why I am using sd_ble_gap_tx_power_set(TX_POWER_LEVEL) function. When I set TX_POWER_LEVEL as 4 or -20, I dont...
We are looking to change tx_power setting to Neg30 dBm and for this we have accessed NRF_RADIO->TXPOWER = (RADIO_TXPOWER_TXPOWER_Neg30dBm << RADIO_TXPOWER_TXPOWER_Pos);
...
I have the NRF51 DK working with CrossWorks on OSX. I have the blinky example working.
Now I would like to figure out how to get very basic HELLO WORLD type demo to iOS...
I am implementing dual bank DFU on the PCA10001 board using the latest SDK (7.2.0) and S110(7.1.0). I am able to enter bootloader from my app as detailed here:
developer...
I'm just reading the documentation regarding the analog digital converter and wonder why there is one bit in the configuration register for every analog input. What will happen...
I'm using a relatively large GATT db that has rd_auth and wr_auth set to true for every characteristic. This prevents the stack from automatically replying with cached values...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
Hello,
I have some questions about the DC/DC conversion factor in nRF51822.
In the datasheet nRF51822_PS v3.1, Figure 11 shows the graph about conversion factor...
I would like to change the device name of the nRF51422 trough a mobile device(Android AND iOS ). The name should be stored even when I disconnect the supply.
From a nordic...
Sir,
We designed a prototype card including "rfd22301" containing nrf51822. We will use in mass production directly the nrf51822.
We will use the BT as a transparent UART...
