Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I don't know how to use nrf52840 dongle as a sniffer. I look at the official routine. It looks like it really doesn't function as a sniffer. Is this what it is. If not, how...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
Hi!
We'd like to include a battery-powered remote control in our Bluetooth mesh network, i.e. we'll have a need for low power consumption.
In our mesh, devices may opt...
Hello everyone. I'm using an nRF51 with SDK 15 for a 'peripheral beacon example'. For compiling, I'm using segger embebbed studio. I have another bluetooth module(looks like...
Hello, I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some recommendations...
Hi all,
Currently i am working on multilink Central and peripheral communication, now i want to do two way communication for the single central and multiple peripherals...
I am trying to use the sdk_config.h file from SDK15 to setup a custom board with a nRF52832. The nRF5283 connects to three SPI peripherals. For ease of software development...
Hi. I'm using nRF52832 SDK 13.0.0 as peripheral.
My device can be always connected by any central.
So some centrals may continue to attempt to connect to my device. I...
Hello!
I am developing a bracelet product base on nrf52832. I have a problem with softdevice's power consumption , when softdevice enabled,the power comsuption will rise...
Hello,
I am developing a basic application on the nrf52832. I am using the SDK14.2 and freertos (two very basic task).
I basically have a problem when I set a uint8...
I want to use app timer to get an power saving delay to wait some external chip operation done. So I use an app timer to set a flag when timer expired and in the wait function...
I need to implement UART service in such a way that it should act as both central and peripheral at a time.
I am using nRF52832 board and SDK 15.
I want to know which...
Using
- nRF5_SDK_15.0.0_a53641a
- gcc-arm-none-eabi-6-2017-q2-update 6.3.1
If I enable APP_TIMER_KEEPS_RTC_ACTIVE in the sdk config, setup the app timer with this...
I am currently working on implementing The Smart Beacon Kit with the Eddystone protocol. I only have basic knowledge in C, but I have successfully implemented the nrf_beacon...
