Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
I always put stand-offs on development boards, when you spill liquid and the DK is on the table top bad things happen, on this nRF5340-PDK when I added a stand off to the...
Hai, I want to connect central to a single peripheral and after certain operations, I want to connect central to more peripherals
I tried with,
#define NRF_SDH_BLE_CENTRAL_LINK_COUNT...
I am working on a case for this project and cannot locate the nRF5340-PDK dimensions. Is there a dimensioned drawing or DXF file? I need to know overall board size and mounting...
Hi!
I've been developing software for nRF52832 devices for a while now, and it's been pretty easy to get into low power modes.
However using the exact same software, but...
Hi, I am working on a project that utilizes the periodic advertisement feature. I have an nrf9160DK as a gateway to synchronize to multiple advertisers. I use the nrf9160...
Dear Members,
How can i keep the data no being cut ?
before using call back function ,
after using call back function :
function :
call back from main :
...
I didn't change nrf5340_cpuapp_common.dts, and I saw the macro definition of "i2c1" in "devicetree_unfixed.h," but I called device_get_binding (DT_LABEL (DT_NODELABEL (i2c1...
Hi,
I found that the startup of the modem (init and connect) is much faster after it has stored some initial information ( I think band-data and so on). This only happens...
Hi,
I have two nRF52 DK boards which i bought one is 2 years old and another 1 year old.. Past week both DK boards are failed to connect with the computers but the power...
We have the following setup:
- nRF52832 XXAA
- SDK 6.0
- S132
I have attempted to add a memory guard into the location preceding the application RAM data block start...
Despite following the procedure listed below, no text appears on the OLED display, despite the driver being able to communicate with the device.
I am using nRF Connect SDK...
I am looking to get some clarification on the QFN94 footprint of the nRF5340. There are four corner pads and they do not appear in the mechanical specifiications section 9...
Hi,
When looking at the reference schematics and reference layout of nRF5340 I notice that pins A25, B12, B26, G1, H2 and J31 are grounded:
Figure 1. Circuit configuration...
