I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi team
We are using your NRF52832 chip for product development based on the official nRF5_SDK_15.0.0_a53641a.
/**@brief Maximum amount of addresses in the whitelist...
I am trying to figure out the maximum transfer size for nrfx_uarte_tx . The documentation says to check the MAXCNT register description in the Product Specification. See page...
Dear,
We are planning to use Raytac Corporation’s BLE module MDBT42Q-512KV2 and which is deployed with Nordic nRF52810 solution. We hope that we can use
nRF SoftDevice...
Hi,
would nRF Connect SDK work smoothly with nRF52810, or is it better to use nRF5 SDK?
If nRF Connect SDK would fit, what would be the influence on electric energy consumption...
Hi nRF
I just bought the new PPK2 tool which I think is awesome. However I think there are some issues with it.
Issue 1:
First of all thy X axis scaling is wrong by...
I want to know how to use control model with interactive pyaci script. I can't see some of the elements with model while using compositiondata_get(). i.e, i can see all client...
Hi, my sdk version is 17.0.2, softdevice is s140, when i use the port pin P1.00 as the RX pin of the uart, it will show data bus error, i have tried use other pin as the RX...
Hello,
I'm writing a firmware for the nrf52840 with a GPS\GSM module connected via UART.
I would like to ask what would be the best library\approach to interact with this...
Hi,
I can't seem to find any example code for nRF51822 on Nordic website. I can only find that softdevice. I am trying to use nRF51822 for some BLE functions.
Thanks,...
Hi Nordic:
It seems that mesh LPN can receive secure beacon via friend node, and if has no friend, LPN also can receive secure beacon if MESH_FEATURE_LPN_ACT_AS_REGULAR_NODE_OUT_OF_FRIENDSHIP...
I'm running some power tests on the nRF52 DK and, after fiddling with some of the power settings, I'm managing to get an idle current of about 1.8uA on the coin cell, and...
I'm sorry to ask a question that I'm sure has been answered before, but I can't find another post similar enough to be of help. I have an HID application that bounces back...
Dear All,
We are currently developing a low power application for the nRF9160, with ncs zephyr version 1.2.0. For our application we want to trigger an interrupt on both...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
