Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I find that the nrf52840DK offers two UART function, and when I running the nrf5_SDK/example/peripheral/uart program, there has only one UART configuration example. Can I...
Hello List,
I have a use case where i need to control 2 DC-motors using a PID-controller. The system is to be controlled via BLE, using a nrf52840 with softdevice S140....
Hi all, I am trying to use the nrf52840 dongle with wireshark, I was having permission errors trying to open the device in the program section of the nrf desktop suite running...
Hello,
we think about using an nrf52820 for a multi role solution. I know from the Compatibility Matrix that the S140 is supported and qualified for the nrf52820. What...
hi,
we are trying to add third sensor to the multi sensor example , new sensor is of type binary_input (0x000F) ZB_ZCL_CLUSTER_ID_BINARY_INPUT.
We are unable to subscribe...
I use nRF Connect for desktop / Bluetooth Low Enery Apps + nRF52840-DK.
When run 'start scan', In rare cases, very small RSSI values (-103dbm, -104dbm ...) may be reported...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
I have a custom board that I have programmed using the UART_BLE example. The code executes and I know I am advertising since LED1 blinks meaning it is advertising but for...
I am testing the Sensor example in the Mesh SDK.
For my implementation I need three properties that are given by the BT Mesh specification. (Properties 0x004F, 0x0057, 0x0059...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
Hello DevZone,
PCA10040 SDK 15.0.0 SD132
I written my own SPIM driver which uses the list function to read in a few bytes. I've set up my list as the example in the...
Hi,
What is the difference between performing a reset by using the function sd_nvic_SystemReset(), and performing a reset by turning the power voltage off and then turn...
I used "nrf5_SDK_for_Mesh_v4.2.0_src.zip" and "nRF5_SDK_V16.0.0", When I used scan_start() command, I saw Light_Switch_Server device and Light_Switch_Client device on the...
We have fabbed a PCB for the nRF52840 that has a QSPI chip. The pins are different from the example in the SDK. I was trying to get the SDK example (examples/peripheral/qspi...
