Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
Hi,
I want to add ble dfu to the hid keyboard example using nRF52810. I have tried unbonded and bonded，both are not work.
By using the bonded way, I made the following...
HI,ALL:
In SDK16, 1 .as topic,when I trigger the mouse_movement_send() and the mouse_click_send() at the same time, Error occurs.
2.how to detect BLE search device sucessfully...
Dear Members,
I tried to find a file *pca10056 project for bsc_rx on ant_plus ?
Can anyone tell me where I can find that file on the SDK ?
Thanks
Visit my lab...
We use a frontend that requires four pins and the timeslot API with our own protocol on nRF52832 & nRF52840. This works fine, but for BLE to work properly we need to leave...
i have a problem with the nRF52 DK (PCA10040) I followed these instructions https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3.1.pdf and the python version is 3.9...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
Hi,
I'm having difficulties running the secure bootloader example (ble_debug version), it doesn't seem to be advertising or providing any logs.
I'm currently using the...
Hi,
I want to create a fresh project in Keil with nRF SDK as static library included into application. I have created the project, but when I run, the code always stuck...
