Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
We just received a batch of custom boards containing the nRF9160. I would like to test them and start developing our actual application.
So far I have switched SW11 to match...
Hi everyone.
I'm using pc_ble_driver_py with nRF52840 USB dongle with burned connectivity_4.1.1_usb_with_s140_6.1.1.hex.
pc_ble_driver_py is modified by me to support...
Hi,
Is there anything to match the above subject with SPI ?
The coding for sending and receiving should be written on the both sides of sensor driver and master side?...
Hi,
I am looking for documentation about the reflow process of the nRF9160, but I cannot find it on the documentation webpage. Is this information available at Nordic? I...
Hello.
When Notifying about 100 bytes of data, sd_ble_gatts_hvx() is sent 5 times. Occasionally NRF_ERROR_RESOUCES occurs. Currently MTU_SIZE is 23, and the actual data...
based on the comments in sdk_config.h, the softdevice uses priorities 0, 1, 4, 5. yet in app_util_platform.h, the macro _PRIO_APP_LOW_MID is given the value of 5. is this...
Hello
I need to do pairing with Android devices without passkey in ble_app_uart example.（ Device nRF52832 ,SDKv16.00, softdevice S132 )
I use ble_app_gls example and Android...
Hi
I am using ble_app_blinky but led is not blinking. I am using P0.27, P0,28, P0.29 pin for LED but in program pin of LED are define as
#define BSP_BOARD_BUTTON_0 0 ...
Hi to everyone. I'm starting developing a bluetooth LE application based on the new Nordic SDK using Zephyr.
I currently have two nrf52_pca10040 boards and I'm trying to...
Hi everyone!
After defining a variable as no_init , my intention is to update its value along the program to debug what was its last state before a random reset.
I am...
Hi !
I am on SDK 15.2 and NRF52832. My peripheral device is on BLE5 and my Central is on BLE4.
I have read that extended advertisement ( up to 256bytes) is a BLE5 functionality...
Hi,
I followed the nRF52840 USB Dongle Antenna has reference layout. I have a small doubt of Antenna matching capacitors(c3,c4,c26) and inductor Should use the same package...
Hi all, I am combining MESH SDK 3.0.0 light switch example client and server with SDK 15.2. I have combined some server code to client and there are no error. And I can use...
hello,
We have developed a custom board corresponding to mbed pca10024 evaluation board.We haven't mounted the rf section and not even the crystal.The only thing that the...
I'm trying to read temperature sensor data through TWI (I2C) from SHT3x using NRF52-DK and SDK v16.0. Observing an oscillator, the address and the return value with CLK looks...
