Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello, I've been tinkering around with the BLE Advertising tutorial on my nRF52840 Dongle (using SoftDevice 140) and I have a question:
How do I configure the dongle's user...
Hi
I have some question about ESB
1. If the noack bit of dynamic payload is set to 0 and transmitted.
Ptx doesn't switch from tx to rx to receive ack?
And prx doesn...
Hello
I use nrf52832 and lithium battery (3.7v, 140 mAh).
I can read the adc value of this battery through the charge IC. I monitored the adc value while charging the...
I find that the nrf52840DK offers two UART function, and when I running the nrf5_SDK/example/peripheral/uart program, there has only one UART configuration example. Can I...
Hello List,
I have a use case where i need to control 2 DC-motors using a PID-controller. The system is to be controlled via BLE, using a nrf52840 with softdevice S140....
Hi all, I am trying to use the nrf52840 dongle with wireshark, I was having permission errors trying to open the device in the program section of the nrf desktop suite running...
Hello,
we think about using an nrf52820 for a multi role solution. I know from the Compatibility Matrix that the S140 is supported and qualified for the nrf52820. What...
hi,
we are trying to add third sensor to the multi sensor example , new sensor is of type binary_input (0x000F) ZB_ZCL_CLUSTER_ID_BINARY_INPUT.
We are unable to subscribe...
I use nRF Connect for desktop / Bluetooth Low Enery Apps + nRF52840-DK.
When run 'start scan', In rare cases, very small RSSI values (-103dbm, -104dbm ...) may be reported...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
I have a custom board that I have programmed using the UART_BLE example. The code executes and I know I am advertising since LED1 blinks meaning it is advertising but for...
I am testing the Sensor example in the Mesh SDK.
For my implementation I need three properties that are given by the BT Mesh specification. (Properties 0x004F, 0x0057, 0x0059...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
